Optimux-108, Optimux-106
Fiber Multi
lexer for 4 E1/T1 and Ethernet or Serial Data
USER ETH INTERFACE
Type
10/100BaseT
Connector
Shielded RJ-45
Throughput
Optimux-108, OP-108C: 100 Mbps
Optimux-106, OP-106C: 75 Mbps
Maximum Frame Size
1536 bytes
V.35 USER INTERFACE
(E1 STANDALONE ONLY)
Type
DCE
Connector
Smart Serial
Throughput
2 Mbps
CONTROL PORT (STANDALONE ONLY)
Type
RS–232 DCE asynchronous
Data Rate
9.6, 19.2, 38.4, 57.6, 115.2 kbps
Connector
Mini-USB 5
ALARM PORT (STANDALONE ONLY)
Type
Dry relay contacts for major and minor
alarms
Connector
RJ-45
STANDALONE INDICATORS
Front Panel
PWR
On (green): both power supplies OK
On (red): power supply A fault
On (yellow): power supply B fault
Off: Both power supplies fault or no
power
LOS/AIS – LINK A/B
On (red): Sync/Signal Loss on Link A/B
On (yellow): AIS detected (products
without Ethernet port only)
Off: normal operation
LOS/AIS – CH1 to CH4
On (red): Signal Loss on channel
On (yellow): AIS received on channel
Off: normal operation
Wavelength
Fiber Type Trans-
mitter
Type
Typical
Power
Output
Receiver
Sensitivity w/o
USER ETH port
Receiver
Sensitivity with
USER ETH port
Typical Max.
Range w/o USER
ETH port
Typical Max.
Range with
USER ETH port
Connector
Type
Extended
Temperature
Version
[nm] [μm] [dBm] [dBm] [dBm] [km] [miles] [km] [miles]
850 62.5/125
multimode
Laser
(VCSEL)
-6 -34 -32 6 3.7 2 1.2 ST, SC,
FC/PC
No
1310 9/125 single
mode
Laser -12 -34 -28 47 29.2 20 12.4 ST, SC,
FC/PC
Yes
1310 62.5/125
multimode
LED -18 -32 -30 7 4.3 2 1.2 ST, SC No
1550 9/125 single
mode
Laser -12 -34 -28 47 29.2 20 12.4 ST, SC,
FC/PC
Yes
1310 9/125 single
mode
Laser (long
haul)
-2 -34 -34 72 44.7 40 24.8 ST, SC,
FC/PC
Yes
1550 9/125 single
mode
Laser (long
haul)
-2 -34 -34 120 74.5 80 49.7 ST, SC,
FC/PC
Yes
Tx: 1310 Rx
1550
9/125 single
mode
Laser WDM
(SF1)
-12 -34 -28 47 29.2 20 12.4 SC No
Tx: 1550 Rx
1310
9/125 single
mode
Laser WDM
(SF2)
-12 -34 -28 47 29.2 20 12.4 SC No
Tx/Rx: 1310 9/125 single
mode
Laser (SF3)
-12 -27 -27 20 12.4 20 12.4 SC/APC only
No
Note: Typical ranges are calculated according to attenuation of 3.5 dB/km for 850 nm multimode fiber, 0.4 dB/km for 1310 nm single mode fiber, and 0.25 dB/km for
1550 nm single mode fiber.
Table 1. Standalone Fiber Optic Interface Characteristics
Order from: Cutter Networks
Ph: 727-398-5252 / Fx: 727-397-9610
(8 strony)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji