RAD Data comm FCD-V35 Instrukcja Użytkownika Pobierz pdf (Strona 6)

 1991–2006 RAD Data Communications Ltd. Specifications are subject to change without prior notice.

All other trademarks are the property of their respective holders.

FCD-E1M, FCD-T1M

odular E1/T1 or Fractional E1/T1 Access Units Supporting Megaplex-

100 Modules

176-100-01/06

www.rad.com

International Headquarters

24 Raoul Wallenberg Street

Tel Aviv 69719, Israel

Tel: 972-3-6458181

Fax: 972-3-6498250

Email: [email protected]

North America Headquarters

900 Corporate Drive

Mahwah, NJ 07430, USA

Tel: (201) 529-1100

Toll free: 1-800 444-7234

Fax: (201) 529-5777

Email: [email protected]

• Control Port (DCE)



Interface: V.24/RS-232



Connector: 9-pin D-type, female



Format: asynchronous



Baud rate: 1.2 to 19.2 kbps,

autobaud



Character: 8 bit no parity, 7 bit

odd or even parity

• Indicators



General: PWR (green), TST

(yellow), MAJ ALM (red), MIN

ALM (red)



Main E1 and Sub-E1: LOC SYNC

LOSS (red), REM SYNC LOSS (red)



Main T1 and Sub-T1:RED SYNC

LOS (red), YEL SYNC LOS (yellow)

• Alarms

Last 100 alarms are stored and

available for retrieval. Each alarm is

time stamped.

• Alarm Relay

3 relay contacts are available on the

control DTE port. The alarm relay is

activated by alarms in the alarm

buffer.

• Physical

Height: 43.7 mm (1.7 in)

Width: 44.4 cm (17.3 in)

Depth: 24.3 cm (9.5 in)

Weight: 1.3 kg (2.9 lb)

• Power

100–240 VAC; 47–63 Hz

-48 VDC, nominal (40-57 VDC)

Power consumption: 6W

• Environment

Temperature: 0°–50°C (32°–122°F)

Humidity: up to 90%,

non condensing

ORDERING

FCD-E1M/*/~/$/&/#+

Modular E1/Fractional E1 access unit

FCD-T1M/*/~/$/&/#+

Modular T1/Fractional T1 access unit

* Specify S1 for optional

drop-and-insert copper E1/T1

sublink

~ Specify power supply voltage:

AC for 100 to 240 VAC

48 for -48 VDC

$ Specify management port interface:

V24 for V.24/RS232 (DB-9)

UTP for Ethernet 10BaseT (UTP)

& Specify data port interface option:

530 for RS-530

V35 for V.35

X21 for X.21

V36 for V.36/RS-449

ETUB for IR-ETH UTP Ethernet

bridge (10BaseT)

ETUQ for IR-ETH/Q UTP Ethernet

bridge with VLAN support

(10BaseT)

ETUR for IR-IP UTP Ethernet router

(10BaseT)

# Specify link connector type:

ST for ST connector

SC for SC connector

FC for FC/PC connector

(Default is for G.703 copper

interface)

+ Specify optional optical interface

wavelength/transmitter type:

85 for 850 nm laser, multimode

13L for 1310 nm laser, single mode

15L for 1550 nm laser, single mode

SUPPLIED ACCESSORIES

AC power cord (when AC power supply

is ordered)

DC adapter plug (when DC power

supply is ordered)

The following cables (suitable for use in

DCE clock mode only) are supplied for

each data port interface specified.

Cable length is 2m (6 ft):

CBL-HS2/V/1/# for 34-pin V.35, DCE

CBL-HS2/R/1/# for 37-pin V.36, DCE

CBL-HS2/X/1/# for 15-pin X.21, DCE

OPTIONAL ACCESSORIES

RM-34

Hardware kit for mounting one unit in

a 19-inch rack

CBL-HS2/*/#

Adapter cables for DB-25 channel

connectors. Cable length is 2m (6 ft).

* Specify interface, clock mode:

V/2/# for 34-pin V.35, DTE1

V/3/# for 34-pin V.35, DTE2

R/2/# for 37-pin V.36/RS-449,

DTE1

R/3/# for 37-pin V.36/RS-449,

DTE2

# Specify cable connector type:

F for female

M for male

Table 2. Ethernet Interface Modules Characteristics

Interface

Module

LAN Table

[addresses]

Filtering and

Forwarding

[fps]

Buffer

[frames]

Delay

[frames]

Line Code WAN Protocol

IR-ETH 10,000 15,000 256 1 Manchester HDLC

IR-ETH/Q 2,000 2,000 256 1 Manchester HDLC

IR-IP – – 256 1 Manchester  PPP (PAP/CHAP)

 Frame Relay (RFC 1490)

 HDLC

Note: All the Ethernet interface modules conform to the IEEE 802.3/Ethernet V2 standard.

Additionally, IR-ETH/Q supports IEEE 802.1/q frames.

1 2 3 4 5 6

FCD-E1M, FCD-T1M 1

Komentarze do niniejszej Instrukcji

Brak uwag

RAD Data comm FCD-V35 Instrukcja Użytkownika Strona 6

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Networking RAD Data comm FCD-V35